S&X Frosted Hexagon Anti-Slip Stickers for Bathtubs & Showers
Soft frosted finish. Family-safe protection.
Oversized 4.7 in (12 cm) frosted hexagons — more than 2× the coverage of typical 3.2 in bathroom stickers — designed for tubs, showers, pool steps, and bathroom floors. The soft frosted finish blends into white, ivory, and light-color surfaces while keeping kids, seniors, and the whole family safe.
Backed by S&X's 25+ years of coated-abrasives expertise, every pack is engineered for reliable, family-safe traction you can trust.
Get it right the first time — under 2 minutes
Watch Before Installation
Why watch before you install?
- Get a leak-proof bond on slick tub and tile surfaces
- Use the included scraper for clean, fingerprint-free placement
- Avoid the #1 reason stickers lift — wet adhesive contact
Install in 4 Simple Steps
Deep Clean
Scrub the tub or tile with bathroom cleaner to remove soap scum, oils, and mildew. Rinse thoroughly with clean water.
Dry Completely
Towel dry, then air-dry for at least 30 minutes. The surface must be 100% bone-dry — no moisture residue.
Plan Layout
Cover only the foot-contact zone where you stand or step — not the entire tub bottom. Typical layout: 8-12 stickers for a bathtub standing area; 8-12 for a walk-in shower; 4-6 per pool step.
Press & Cure
Peel the backing and apply each hexagon. Press firmly with the included scraper (or a dry cloth) for 30 seconds, working from center outward to push out air bubbles. Wait 24 hours before any water contact.
Important Precautions
-
24-Hour Cure: Wait a full 24 hours after install before showering, bathing, or any water exposure. Premature water contact will lift the adhesive.
-
Surfaces: Avoid textured anti-slip coatings, peeling refinish, freshly caulked seams, or cracked glaze. Repair or replace damaged surfaces first.
-
Removal: Warm with a hair dryer, then lift an edge with the included scraper or a plastic card. Use rubbing alcohol for any adhesive residue.
Surface Guide
Why It Works
Family-Safe Traction
Wet-grip surface designed for kids, seniors, and the whole family.
Wet-Surface Hold
Bathroom-grade adhesive bonds securely on tubs, tile, and pool steps.
Frosted Translucent Finish
Frosted hexagons blend softly into white, ivory, and light-color tubs.
Mildew-Resistant Bond
Sealed edges resist daily moisture and bathroom chemistry.
- Clean weekly with a non-abrasive bathroom cleaner.
- Avoid bleach, steel wool, and abrasive scrubbers.
- Inspect edges monthly; replace any sticker that begins to lift.
- Allow the tub to fully dry between uses to extend lifespan.
- Engineered for foot contact only — leave the bathing area uncovered. Prolonged contact with bare skin can feel rough and may chafe sensitive areas during a soak.
- Plan to replace every 12-18 months — natural adhesive aging may cause slight tinting that does not affect anti-slip performance.
- Warm each sticker with a hair dryer for about 30 seconds.
- Lift an edge with the included scraper or a plastic card.
- Peel slowly at a low angle to avoid surface marks.
- Clean any residue with rubbing alcohol or adhesive remover.
Frequently Asked Questions
1.Will it stay stuck in a wet tub?
Yes. Once the 24-hour cure is complete, the bathroom-grade adhesive is fully water-resistant and rated for daily submersion in standing water and direct shower spray.
2.How many do I need for my bathtub or shower?
For most homes, one 24-pack covers a complete bathroom. Cover only the foot-contact zone where you stand or step. Leave the area where you lie or sit uncovered — the frosted grip is engineered for foot contact only, and prolonged contact with bare skin during a soak can feel rough and may chafe sensitive areas. Typical layout: 8-12 stickers for a bathtub standing area; 8-12 for a walk-in shower; 4-6 per pool step. Because each hexagon is oversized at 4.7 in (12 cm), the 24-pack typically covers one tub plus a separate shower, with extras for replacement.
3.Are they safe for kids and seniors?
Yes. The grip texture is non-abrasive on bare skin, the rounded hex edges have no sharp corners, and the soft frosted finish does not create the visual confusion that high-contrast strips can cause for elderly users.
4.What does the frosted finish look like on different tubs?
On white, ivory, beige, and light-color tubs the frosted hexagons create a soft, decorative look that blends gently into the surface. On dark tubs, glass, or richly colored tile the outline will be more visible. Lay out a few stickers without peeling the backing first to preview placement before final installation.
5.Will mold grow under the stickers?
Not when applied correctly. A clean, fully dry surface plus the 24-hour cure creates a sealed bond that blocks moisture infiltration. Inspect monthly and replace any sticker showing dark edges.
6.How do I remove them without damaging my tub?
Warm each sticker with a hair dryer for about 30 seconds, slide the included scraper or a plastic card under one edge, peel slowly at a low angle, then clean any residue with rubbing alcohol. Acrylic, fiberglass, ceramic, and porcelain surfaces will not be damaged when removal is done gradually.
7.Will the stickers turn yellow over time?
Yes, like most clear bathroom adhesives, the stickers may gradually take on a slight yellow tint after prolonged sunlight exposure — typically 12+ months in well-lit bathrooms or pool areas. This is a natural aging of the bonding adhesive and does not affect anti-slip performance — the grip surface stays the same. We recommend replacing the stickers every 12-18 months in daily-use showers, or every 24+ months for occasional use, as part of normal bathroom maintenance.