Product Support Page

S&X Anti-Slip Tape with Reflective + Glow-in-the-Dark Stripes

Reliable traction. 24/7 visibility.

Engineered for round-the-clock visibility — combining a high-reflection stripe (visible under direct light) with a photoluminescent glow stripe (charges in light, glows in darkness). Ideal for stairs, ramps, hazard zones, and emergency exits where uninterrupted visibility is critical.

Backed by S&X's 25+ years of coated-abrasives expertise, every roll is engineered for reliable, long-lasting performance you can trust.

Rolls: 6" × 60 ftPre-Cut: 6" × 24"Indoor & Outdoor

Watch Installation Video

Get it right the first time — under 2 minutes

Watch Before Installation

Why watch before you install?

Ensure proper installation for maximum safety
Get the best performance and long-lasting results
Avoid common mistakes and save time

Install in 4 Simple Steps

1

Clean & Prep

Wipe with isopropyl alcohol. Surface must be clean, dry, and free of dust or grease.

2

Spot Test

Test on an inconspicuous area first to confirm surface compatibility.

3

Measure & Cut

Cut to length with sharp scissors. Round the corners to prevent edge lifting.

4

Apply & Bond

Peel the release film and apply. Place the film over the grit, then press firmly with a scraper. Allow 24h to cure.

Important Precautions

Temp Control: Apply only when surface is at least 10°C (50°F). Pre-warm if cold.
Surfaces: Avoid raw wood, porous concrete, or submerged areas. Prime/seal first.
Removal: Heat with a hair dryer, then peel slowly to minimize adhesive residue.

Surface Guide

Recommended Surfaces

Concrete

Metal

Tile

Sealed Wood

Glass

Fiber Cement

Avoid or Prepare First

Dusty Surface

Oily Surface

Wet Surface

Peeling Paint

Loose Coating

Cracked Surface

Why It Works

Max Grip

60-grit aggressive surface delivers superior traction and confident footing.

Reflective Visibility

High-reflection stripe provides bright visibility under direct light, even from distance.

Glow-in-the-Dark

Light-absorbing stripe charges with ambient light and glows for hours after dark.

Heavy-Duty Build

Reinforced multi-layer construction with industrial-strength adhesive.

Care & Maintenance

Clean regularly with mild soap and water.
Avoid harsh chemicals and solvents.
Inspect periodically and replace if worn.
Keep stripes clean and dry to maintain both reflective and glow performance.

Safe Removal

Warm the tape with a heat gun or hair dryer.
Peel back slowly at a low angle.
Remove any residue with adhesive remover.
Test on a small area first.

Frequently Asked Questions

1.What surfaces does it work on?

Concrete, metal, tile, sealed wood, glass, and fiber cement work best. See the Surface Guide above for details.

2.Can it be used outdoors?

Yes. Both the reflective and glow-in-the-dark stripes are designed for indoor and outdoor use, including hazard zones, emergency exits, and outdoor walkways.

3.How long will it last?

Lifespan depends on traffic and conditions, typically 12-24 months in normal use. Both visibility stripes maintain their function throughout normal product life. Inspect periodically and replace when worn.

4.Can it get wet?

Yes, the tape is water-resistant once installed. Both stripes function in wet conditions. Make sure the surface is fully dry before applying.

5.How do I remove the tape?

Warm with a hair dryer, peel slowly at a low angle, then clean any residue with adhesive remover.

6.How does S610RG provide 24/7 visibility?

S610RG combines two visibility technologies in one product: a high-reflection stripe that returns light from headlights and flashlights (active visibility), and a photoluminescent stripe that charges with ambient light and glows in darkness (passive visibility). Together they ensure the tape remains visible across daytime, low-light, and complete darkness — ideal for hazard zones, emergency exits, and 24-hour operations.