Product Support Page

S&X Heavy-Duty Anti-Slip Tape with Hazard Warning Stripes

Reliable traction. Industrial strength.

Engineered for industrial and heavy-traffic environments — factory floors, machine bases, loading docks, and outdoor steel ramps. The reinforced multi-layer construction resists scuffs, tears, and abrasion in the toughest conditions.

Backed by S&X's 25+ years of coated-abrasives expertise, every roll is engineered for reliable, long-lasting performance you can trust.

Rolls: 1"-12" × 33 / 60 ftPre-Cut: 6" × 24" / 30"Indoor & Outdoor

Watch Installation Video

Get it right the first time — under 2 minutes

Watch Before Installation

Why watch before you install?

Ensure proper installation for maximum safety
Get the best performance and long-lasting results
Avoid common mistakes and save time

Install in 4 Simple Steps

1

Clean & Prep

Wipe with isopropyl alcohol. Surface must be clean, dry, and free of dust or grease.

2

Spot Test

Test on an inconspicuous area first to confirm surface compatibility.

3

Measure & Cut

Cut to length with sharp scissors. Round the corners to prevent edge lifting.

4

Apply & Bond

Peel the release film and apply. Place the film over the grit, then press firmly with a scraper. Allow 24h to cure.

Important Precautions

Temp Control: Apply only when surface is at least 10°C (50°F). Pre-warm if cold.
Surfaces: Avoid raw wood, porous concrete, or submerged areas. Prime/seal first.
Removal: Heat with a hair dryer, then peel slowly to minimize adhesive residue.

Surface Guide

Recommended Surfaces

Concrete

Metal

Tile

Sealed Wood

Glass

Fiber Cement

Avoid or Prepare First

Dusty Surface

Oily Surface

Wet Surface

Peeling Paint

Loose Coating

Cracked Surface

Why It Works

Max Grip

Industrial-grade aggressive surface delivers superior traction even under heavy loads.

Multi-Layer Build

Reinforced solid core resists scuffs, tears, and impact damage in demanding environments.

Waterproof

Weatherproof construction stands up to rain, washdowns, and outdoor exposure.

Heavy-Duty Adhesive

Industrial-strength adhesive engineered for the toughest applications.

Care & Maintenance

Clean regularly with mild soap and water.
Avoid harsh chemicals and solvents.
Inspect periodically and replace if worn.
Replace promptly if hazard warning stripes become heavily scuffed — high-visibility marking is the primary safety function.

Safe Removal

Warm the tape with a heat gun or hair dryer.
Peel back slowly at a low angle.
Remove any residue with adhesive remover.
Test on a small area first.

Frequently Asked Questions

1.What surfaces does it work on?

Concrete, metal, tile, sealed wood, glass, and fiber cement work best. See the Surface Guide above for details.

2.Can it be used outdoors?

Yes. The reinforced PET backing and weatherproof adhesive are built for outdoor industrial applications, including loading docks, ramps, and outdoor walkways.

3.How long will it last?

Lifespan depends on traffic load and conditions. In normal use, S680 typically outlasts standard residential-grade tapes. Inspect periodically and replace when warning stripes are heavily worn.

4.Can it handle vehicle or forklift traffic?

S680 is rated for pedestrian use and light equipment traffic. For continuous direct vehicle wheel traffic (forklifts, carts), use S680 as a hazard warning marker visible at distance, rather than a continuous traffic surface. Heavy direct vehicle wheel traffic shortens the lifespan of any anti-slip tape.

5.How do I remove the tape?

Warm with a hair dryer, peel slowly at a low angle, then clean any residue with adhesive remover.

6.How is S680 different from standard anti-slip tape?

S680 uses a reinforced multi-layer construction designed for heavy-duty industrial use. The yellow and black hazard warning stripe provides high-visibility marking, while the scuff-proof base resists tears, abrasion, and moisture better than standard residential-grade tapes. Ideal for factory floors, loading docks, machine bases, and outdoor industrial walkways.